편집

다음을 통해 공유

Enable-NetAdapterLso

Module:
NetAdapter Module

Enables LSO properties, such as LSOv4 and LSOv6, of the network adapter.

Syntax

ByName (Default) 

Enable-NetAdapterLso
    [-Name] <String[]>
    [-IncludeHidden]
    [-IPv4]
    [-IPv6]
    [-NoRestart]
    [-PassThru]
    [-CimSession <CimSession[]>]
    [-ThrottleLimit <Int32>]
    [-AsJob]
    [-WhatIf]
    [-Confirm]
    [<CommonParameters>]

ByInstanceID 

Enable-NetAdapterLso
    -InterfaceDescription <String[]>
    [-IncludeHidden]
    [-IPv4]
    [-IPv6]
    [-NoRestart]
    [-PassThru]
    [-CimSession <CimSession[]>]
    [-ThrottleLimit <Int32>]
    [-AsJob]
    [-WhatIf]
    [-Confirm]
    [<CommonParameters>]

InputObject (cdxml) 

Enable-NetAdapterLso
    -InputObject <CimInstance[]>
    [-IPv4]
    [-IPv6]
    [-NoRestart]
    [-PassThru]
    [-CimSession <CimSession[]>]
    [-ThrottleLimit <Int32>]
    [-AsJob]
    [-WhatIf]
    [-Confirm]
    [<CommonParameters>]

Description

The Enable-NetAdapterLso cmdlet enables the state of the large send offload (LSO) settings, such as LSOv4 and LSOv6, on the network adapter. If LSOv4 or LSOv6 are not specified, then both LSOv4 and LSOv6 are enabled. LSO is a technology in which the work of segmenting data into network frames is performed by the network adapter instead of by the TCP/IP stack. With LSO, TCP/IP sends very large data packets down to the network adapter driver and the network adapter hardware. The network adapter separates the data into smaller network-sized frames. This increases the speed of high-end send operations and decreases the processor usage of the computer, because the work is performed on the network adapter. To enable just LSOv4 or LSOv6, run the Set-NetAdapterLso cmdlet.

Examples

Example 1: Enable LSO for IPv4 and IPv6 on all visible network adapters

PS C:\> Enable-NetAdapterLso -Name "*"

This command enables LSO for both IPv4 and IPv6 on all visible network adapters and restarts the network adapters.

Example 2: Enable LSO for IPv4 and IPv6 on all visible network adapters

PS C:\> Enable-NetAdapterLso -Name "*" -IPv4 -IPv6

This command enables LSO for both IPv4 and IPv6 on all visible network adapters by explicitly specifying the parameters and then restarts the network adapters.

Parameters

-AsJob

Runs the cmdlet as a background job. Use this parameter to run commands that take a long time to complete. The cmdlet immediately returns an object that represents the job and then displays the command prompt. You can continue to work in the session while the job completes. To manage the job, use the *-Job cmdlets. To get the job results, use the Receive-Job cmdlet. For more information about Windows PowerShell® background jobs, see about_Jobs.

Parameter properties

Type:SwitchParameter
Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-CimSession

Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local computer.

Parameter properties

Type:

CimSession[]

Default value:None
Supports wildcards:False
DontShow:False
Aliases:Session

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-Confirm

Prompts you for confirmation before running the cmdlet.

Parameter properties

Type:SwitchParameter
Default value:False
Supports wildcards:False
DontShow:False
Aliases:cf

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-IncludeHidden

Indicates that the cmdlet includes both visible and hidden network adapters in the operation. By default only visible network adapters are included. If a wildcard character is used in identifying a network adapter and this parameter has been specified, then the wildcard string is matched against both hidden and visible network adapters.

Parameter properties

Type:SwitchParameter
Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

ByName
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False
ByInstanceID
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-InputObject

Specifies the input to this cmdlet. You can use this parameter, or you can pipe the input to this cmdlet.

Parameter properties

Type:

CimInstance[]

Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

InputObject (cdxml)
Position:Named
Mandatory:True
Value from pipeline:True
Value from pipeline by property name:False
Value from remaining arguments:False

-InterfaceDescription

Specifies an array of network adapter interface descriptions. For a physical network adapter this is typically the name of the vendor of the network adapter followed by a part number and description, such as Contoso 12345 Gigabit Network Device.

Parameter properties

Type:

String[]

Default value:None
Supports wildcards:False
DontShow:False
Aliases:ifDesc, InstanceID

Parameter sets

ByInstanceID
Position:Named
Mandatory:True
Value from pipeline:False
Value from pipeline by property name:True
Value from remaining arguments:False

-IPv4

Indicates that this cmdlet affects IPv4 traffic.

Parameter properties

Type:SwitchParameter
Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-IPv6

Indicates that this cmdlet affects IPv6 traffic.

Parameter properties

Type:SwitchParameter
Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-Name

Specifies an array of network adapter names.

Parameter properties

Type:

String[]

Default value:None
Supports wildcards:False
DontShow:False
Aliases:ifAlias, InterfaceAlias

Parameter sets

ByName
Position:0
Mandatory:True
Value from pipeline:False
Value from pipeline by property name:True
Value from remaining arguments:False

-NoRestart

Indicates that the cmdlet does not restart the network adapter after completing the operation. Many advanced properties require restarting the network adapter before the new settings take effect.

Parameter properties

Type:SwitchParameter
Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-PassThru

Returns an object representing the item with which you are working. By default, this cmdlet does not generate any output.

Parameter properties

Type:SwitchParameter
Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-ThrottleLimit

Specifies the maximum number of concurrent operations that can be established to run the cmdlet. If this parameter is omitted or a value of 0 is entered, then Windows PowerShell® calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer. The throttle limit applies only to the current cmdlet, not to the session or to the computer.

Parameter properties

Type:Int32
Default value:None
Supports wildcards:False
DontShow:False

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

-WhatIf

Shows what would happen if the cmdlet runs. The cmdlet is not run.

Parameter properties

Type:SwitchParameter
Default value:False
Supports wildcards:False
DontShow:False
Aliases:wi

Parameter sets

(All)
Position:Named
Mandatory:False
Value from pipeline:False
Value from pipeline by property name:False
Value from remaining arguments:False

CommonParameters

This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.

Inputs

CimInstance

The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.

Outputs

CimInstance

The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.